Connector 6 Remove upper exit cover, and open the lower exit cover. Heat roller at ready temperature? C-C cross-section Mirror mylar sheet Guide mylar sheet 2 locations Mirror seal B-B cross-section Mar. Bracket 4 Remove the toner auger motor 2 screws and bundling band. Then remove the transport clutch. Note: For reassembling, refer to the service hand- book 1. This is the one used by company people for their internal use and hence many of them are copyrighted by respective companies. When assembling, make sure that the thermostat is attached as shown in the figure on the right.
When the thermostat detects an abnormality, the thermostat must be replaced to- gether with the other damaged parts in the fuser. Make sure that sensor pins are firmly fit- ted into the bracket holes. Do not touch the surface of the power supply roller directly with your hands. Initial alignment started Initial alignment completed? After assembly, make sure that the power supply roller rotates smoothly, and moves vertically smoothly by the spring. When the toner density drops, a fixed amount of toner is added from the toner hopper. Cushions Fixing reference: Clearance 0 to 0.
Note: Wiring is as follows. Claw Base frame floor side Mar. This is the one used by company people for their internal use and hence many of them are copyrighted by respective companies. Note: Adjustment of the main blade, recovery blade and fur brush cleaner unit is not necessary. Resistor R27 is for stopping the watchdog timer, and is normally not mounted. Cleaning roller 1 E-ring Cleaning roller 2 Spring black Spring silver Rear side Mar. Do not touch the charger wire directly with your hands or fingers.
If the temperature becomes abnormally hot, the power to the heater lamps is cut by a thermostat. Plate spring Plate spring Mirror 1 Mar. The original size is displayed by the yellow lines on the indicator and carriage 1. Do not directly touch the blade edge by hand. Front side Rear side 2: Also, when handling the unit, take suffi- cient care not to hold the adjustment sec- tion and the lens. Mirror 2 is described later on. These server access are the main resource of our library.
We have tried utmost care to make sure completeness of manual. Nozzle mixer Oil seal 6 After removing the 2 bearings with the C-ring Oil seal pliers, remove the 2 oil seals. Set screw Aligning motor Flange Pulley Mar. These server access are the main resource of our library. Before installing the lower damp heater unit, check the power voltage. This guide is made of material that prevents electrification caused by friction with the paper.
Note: When installing the aligning unit, prevent the two leaf springs from becoming bent. They are also used for detecting paper jams. Manual separation roller 3 Remove the clip and draw out the manual sepa- ration roller from the shaft. If a signal which has the same characteristics is received by the phototransistor, an original is determined to be present. The switch is also used for paper jam detection. This operation is repeated until all stacked paper is copied. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise noted in this manual or other related documents.
Left top cover 1 Remove the 2 screws. Stamped mark Exit roller 1 Remove the front and rear stop ring, then re- move the exit roller. This is set at the point when the trailing edge of the output original has passed the exit sensor in the one-sided mode. Handle 3 Take off the top screw of link, and then remove the 2 guides 2 screws for each. We are also looking for any opportunity to exchange both server access and service manuals and anyone interested can contact us. Do not allow the charger wire to be twisted.
Clearance must be 0 to 2mm. Note: When assembling, align the cut surface of the pulley with the one of the shaft. Enjoy your Toshiba 5570 Copier Service Manual and please do not forget to like us on facbook or leave feedback. We are slowly increasing availability of service manuals on this website and if you can not find what you are looking for, please contact us and we will be happy to provide you if we can get hold of it. Connector cable bracket 5 Disconnect the motor connector. Surface temperature of heat roller: 200°C Thermistor resistance value: about 0.
Flapper rubber skirt Flapper rubber skirt Arrow view Mar. Many people ask us from where do we get all these manuals. Tray sheet guides Fixing reference: 0 to -0. Thermistor connector 6 Remove the thermostat 2 screws. The drum surface is cleaned. Handle bracket 7 Remove the timing belt. Construction of the image processing section Mar.
Just to clarify, we are a big service provider for almost all electronic items and hence we have server access to majority of company website. Thin wire Blue White Black Yellow Yellow connector Transparent connector Blue White Blue White Thick wire Mar. Guide mylar sheet 2 Guide mylar sheet 2 3 locations A-A cross-section Mar. In real world we hardly see Toshiba 5570 Copier Service Manual in paperback or softcopy and hence we have created this website which will give you access of such a huge collection of service manuals at a rock bottom price. Developer bias 3 Remove the motor unit 3 screws.