Piston Ring Groove Width Standard: 0. Observe all the rules listed below. Main Fuse 30 A 15. Run the air cleaner drain hose, fuel tank drain hose and fuel tank breather hose into the hole of the heat insulation rubber plate. . Genuine parts provided as spare parts are listed in the Parts Catalog.
Torque - Cylinder Head Cover Bolts: 9. It is specifically written for the do-it-yourselfer as well as the experienced mechanic. Instead, the vapors are routed through an oil separator to the inlet side of the engine. The chart gives a time schedule for required maintenance operations. Replace the shim with one of a different thickness. Torque - Stator Coil Bolts: 12 N·m 1. Refer to the appropriate sections of this manual for service limits on individual parts.
If the free play is incorrect, adjust the throttle cables. Circlips, Cotter Pins Replace the circlips or cotter pins that were removed with new ones. Among those acts presumed to constitute tampering are the acts listed below. Clamp Hold the rear brake hose. They could be damaged, requiring replacement.
Run the left turn signal light lead, right turn signal light lead and license plate light lead into the hole. See the table below for correct bolt and nut usage. Dry Mass 164 kg 362 lb Curb Mass: Front 95 kg 209 lb Rear 97 kg 214 lb Fuel Tank Capacity 17 L 4. . The Periodic Maintenance Chart is located in the Periodic Maintenance chapter.
Storage of Removed Parts After all the parts including subassembly parts have been cleaned, store the parts in a clean area. Run the gear position switch lead to the right side of the water hose connected to the oil cooler. The simple fluid changes that you pay hundreds for are covered as well as any repair you can think of. When this accumulation is suspected or observed, flush the cool- ing system. If the specified tightening sequence is not indicated, tighten the fasteners alternating diagonally. The clearance can be out of the specified range because of the shim tolerance. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Exhaust Emission Control System This system reduces the amount of pollutants discharged into the atmosphere by the exhaust of this motorcycle. Run the gear position switch lead between the water hoses. But it should be adjusted harder for high speed riding or riding with a passenger. Front Wheel Rotation Sensor Lead 5. Just imagine how much you can save by doing simple repairs yourself.
If the input voltage is out of the standard, check the wiring for continuity see Stick Coil Circuit. In- stead, fuel vapors are routed into the running engine to be burned, or stored in a canister when the engine is stopped. . Main Fuse 30 A 7. The push rod does not return to its original position once it moves out to take up camshaft chain slack. Torque - Exhaust Butterfly Valve Actuator Pulley Bolt: 4.
Breather Hose Blue Paint 5. Clutch Plate Assembly Length — — — 2. Diode Circuit Inspection 1-11, 2-11, 12-13, 12-15, 12-16, 13-14, Tester Connection 13-15 The resistance should be low in one direction and more. Some manuals actually cover more items that are not even listed! Gaskets, O-rings, oil seals, grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled. Battery 12 V 8 Ah 6.
This Will warp the cylinder head. Disconnect the ground cable — first and then the positive +. This may cause it to fracture, causing extensive engine damage. They are specifically written for the do-it-yourself-er as well as the experienced mechanic. Seat Height 820 mm 32. Water hose to Oil Cooler 3.
Electrical Wires A two-color wire is identified first by the primary color and then the stripe color. Make sure the area is well venti- lated and free from any source of flame or sparks; this includes any appliance with a pilot light. Install the rubber cover onto the radiator cap. Match clearance in vertical column with present shim size in horizontal column. If there is no vacuum pulsation, check the hose line for leak. .