Set a timing light to the ignition coil power supply line intermediate connector No. D Gently shake the connector up, down and to the left and right. The objects to be checked are connectors and components which are indicated by inspection procedures or given as probable causes which generates diagnosis codes or trouble symptoms. The larger the number, the greater the bolt strength. A B Rear door The illustration indicates right outer side. D Check the oil pan sealant-coated surface for damage and deformation. If no, repeat the operation in steps 13 to 17 above.
Touch the pin directly with the test bar. For detailed information concerning the inspection, checking, adjustment, disassembly and reassembly of the engine, transmission and major components after they have been removed from the vehicle, please refer to separate manuals covering the engine and the transmission. D Removal steps: The part designation number corresponds to the number in the illustration to indicate removal steps. D Check all boots and breather hoses for cracks and damage. Drive pattern for air bleeding Close the throttle valve.
The front impact sensors are installed in the headlamp support. Degrease the sealant-coated surface and the engine mating surface. Intake Manifold Vacuum Check 10. Complete step-by-step instructions, diagram's, illustration's, wiring schematics, and specifications to completely repair your vehicle with ease! We use the most popular pdf document viewer called. The clock spring is installed in the steering column. Download link: Complete digital service and repair manual written for the Mitsubishi Montero Sport ; Production model years: 1999-2002. Tighten the bolts in order of the numbers shown in the illustration.
For any problem to download, please contact me at office workshoprepairmanuals. Insert the setting pin into the pin holes once they are aligned. Check that the timing marks of the right bank side exhaust camshaft sprocket is aligned, and clamp the timing belt with a clip. Be sure to use attachments which are high enough, or remove the side step if not using attachments. Explanation of Manual Contents 4.
Loosen the centre bolt of the tension pulley, and then remove the timing belt. Symbols for Lubrication, Sealants and Adhesives Information concerning the locations for lubrica- tion and for application of sealants and adhe- sives is provided, by using symbols, in the dia- gram of component parts or on the page follow- ing the component parts page, and explained. Be careful not to insert these bolts at an angle. D Transmission: Neutral P range for automatic transmission D Air conditioner and heater: Not operational D Engine coolant temperature: 83°C or higher 5 Stop the engine. Mitsubishi Montero Sport 1999 2000 2001 2002 Service Repair Manual Pdf Mitsubishi Montero Sport 1999 2000 2001 2002- The Best Manuals are available at the distance of just a click! If the air inside the lash adjusters is then released, the operation of the lash adjusters will return to normal.
Your 2003 Mitsubishi Montero parts correspond with the number of pages printed on it in this manual, very easy to use. Caution At this time, be careful not to short the connector pins with the test bars. D Do not put oily rags in pockets, the use of overalls without pockets will avoid this. In order to ascertain the conditions under which an intermittent malfunction occurs, first ask the customer for details about the driving conditions, weather conditions, frequency of occurrence and trouble symptoms, and then try to recreate the trouble symptoms. Compared to the electronic version and paper version , there is a great advantage. Do not place anything on top of it. Vehicle Information Code Plate 16.
If anyone happens to have had this same issue in the past and has a solution or recommendations to provide, that would be very much appreciated as well. Check that ignition timing is at the standard value. D Installation steps: Specified in case installation is impossible in reverse order of removal steps. Set the timing belt onto the crankshaftsprocket. Run the engine at idle for 1 - 3 minutes to let it warm up. It covers every single detail on your car. No diagnosis code After taking note of the malfunction code, erase the diagnosis code memory Recheck trouble symptom.
You need only Adobe Reader installed! If any tool than specified is used, damage to the harness and other components will result. When repainting original parts, do so after first mask- ing the theft-protection label, and, after painting, be sure to peel off the masking tape. Right side is symmetrically opposite. Before inspection, set the vehicle to the pre-inspection condition. If this is not done, there is the possibility of semiconductor parts being damaged.